Quiz HP3-F18: HP OneView

The correct answer is A. power delivery infrastructure representation.
To identify hot spots in HP server racks and optimize cooling, you need a view of the power and heat distribution across the rack and datacenter environment. Power delivery infrastructure representation provides a visual representation of how power is delivered through the datacenter infrastructure, which helps you understand load patterns and locate areas where power consumption is concentrated. These concentrated areas often correspond to hot spots.
Why A is correct:
- It helps visualize power distribution in the datacenter.
- Areas with higher power draw usually generate more heat.
- This makes it useful for spotting thermal problem areas in racks.
Why the other options are not correct:
- B. Intelligent Power Discovery (iPDUs): These are intelligent power distribution units used to monitor and manage power at the outlet level, but they are not the best tool specifically for identifying rack hot spots.
- C. physical asset location: This helps you locate equipment physically, but it does not directly show heat or power concentration.
- D. 3D Datacenter View: This provides a spatial view of the datacenter, but the question is specifically about identifying hot spots, which is better addressed by power delivery infrastructure representation.
In short, power delivery infrastructure representation is the most appropriate tool because it helps you map power usage, which is directly tied to heat generation and hot spot identification.

The correct answer is C. SNMP Receiver
In HP OneView, the SNMP Receiver is the component that handles incoming SNMP traps. Its job is to receive those traps and translate them into notification messages that are then passed on to the Alert Service.
Why the other options are incorrect:
A. Events Service
This service is generally involved in processing and managing events, but it is not the specific component responsible for receiving and translating SNMP traps.
B. Alerts Service
The Alert Service is the target that receives the notification messages, not the part that translates the traps.
D. Status Aggregation Service
This service focuses on combining and summarizing health or status information, not on trap translation.
So, the SNMP Receiver is the correct answer because it acts as the gateway for incoming SNMP traps and forwards the resulting notifications to the Alert Service.

The correct answer is B. Hardware Type.
When you create a server profile, the Hardware Type setting defines the profile’s remove-and-replace behavior for a server blade. This setting tells the management system what kind of physical server hardware the profile is expected to run on, and it helps determine how the profile can be reapplied if the blade is removed and replaced.
Why the other options are incorrect:
A. Enclosure Group
This setting defines the enclosure-related configuration, such as networking and interconnect behavior, but it does not control the remove-and-replace behavior of the server blade itself.
C. Affinity
Affinity relates to how tightly a profile is bound to a specific server, but it is not the setting that determines the remove-and-replace behavior.
D. Baseline
A baseline is usually associated with configuration consistency or comparison, not with blade replacement behavior.
In short, Hardware Type is the profile setting that determines how a server profile behaves when a blade is removed and replaced.

The correct answer is A. on the HP OneView login page.
If you forget the HP OneView Administrator password and there are no other administrator accounts available, the password reset option is accessed from the HP OneView login page. This is where the system provides the recovery or reset workflow for the administrator account.
Why the other options are incorrect:
B. in the HP OneView application console
This is not where you would initiate a password reset when you cannot log in. The application console requires access, which you do not have if the administrator password is lost.
C. on the Credential Service
The Credential Service is used for managing stored credentials, but it is not the place to reset the HP OneView Administrator password.
D. at the reset challenge key
This is not the location of the reset option. While a challenge key or similar recovery mechanism may be part of the reset process, it is not where you locate the reset option itself.
So the reset option is found on the HP OneView login page.

The correct answer is B. from the bottom up by creating rack PDUs
HP OneView can manage power topology for devices that are not HP intelligent powered devices by modeling the physical power chain manually. Since these old servers do not provide intelligent power data, OneView cannot automatically discover their power relationships the way it can with supported intelligent devices.
In this situation, the power topology must be built from the bottom up. That means you start by defining the rack PDUs, which are the power sources in the rack, and then associate the downstream devices such as servers to those PDUs. This creates the manual power configuration needed for OneView to understand how power is distributed.
Why the other options are incorrect:
A. with a parent device
This is too vague and does not describe the correct method for constructing the manual power topology in OneView for non-intelligent devices.
C. from the top down using Location Discovery Services
Location Discovery Services may help with identifying devices and locations, but it is not the method used to build manual power topology for old non-intelligent servers.
D. by configuring the intelligent iPDU on the server
An intelligent iPDU is a power distribution unit, not something configured on the server itself. Also, these servers are specifically described as not HP intelligent powered devices, so this does not apply.
Summary:
For non-intelligent legacy servers, HP OneView builds the manual power topology starting at the rack PDU level and working upward/downstream from there. That is why B is correct.

The correct answer is A. Connect-HPOVMgmt.
When working with the HP OneView PowerShell library, you need to establish an authenticated session with the HP OneView appliance before you can manage resources or issue commands. The cmdlet used for that login/authentication step is Connect-HPOVMgmt.
Why the other options are incorrect:
- B. Set-HPOVResource: This would be used to modify or update an existing resource, not to authenticate.
- C. Send-HPOVRequest: This is typically used to send a request to the appliance or API after you are already connected, not to create the initial authenticated session.
- D. New-HPOVResource: This would be used to create a new resource in the environment, not to log in.
So the sequence is generally:
1. Use Connect-HPOVMgmt to authenticate.
2. Use other cmdlets like Set-HPOVResource, Send-HPOVRequest, or New-HPOVResource to manage resources once connected.
Therefore, A is the correct choice.

The correct answers are B. single unified management view and E. accelerated Cloud and Convergence.
Why B is correct:
HP SDDC (Software Defined Data Center) is about simplifying and unifying the management of data center resources. A single unified management view is a major selling point because it helps customers reduce complexity, improve operational efficiency, and manage compute, storage, and networking from one place.
Why E is correct:
Accelerated Cloud and Convergence is another key motivation for adopting HP SDDC. Customers are often looking to move faster toward cloud-style infrastructure and converged systems. HP SDDC helps accelerate that transition by making the data center more agile, automated, and aligned with cloud and converged IT goals.
Why the other options are not the best choices:
A. advanced server security
Security is important, but it is not one of the primary motivating factors emphasized when promoting HP SDDC in this question.
C. improved storage compression
Storage compression is a useful storage feature, but it is too narrow and not a central business motivation for HP SDDC.
D. enhanced application monitoring
Application monitoring is valuable, but it is not the main focus of HP SDDC promotion here. The question is asking about the broader customer motivations, which are management simplicity and cloud/converged acceleration.
In summary, the two factors to highlight are:
B. single unified management view
E. accelerated Cloud and Convergence

The correct answer is C. Use the Insight Control Management appliance to run in Update-only mode.
The key detail in the question is that the customer already has an existing server environment with G5 and newer HP ProLiant servers, and those servers are currently managed by HP SIM with Insight Control. The customer now wants to implement HP OneView as the new management platform.
The best approach is not to try to force all existing servers into HP OneView management, because HP OneView does not manage every older ProLiant generation in the same way, and the environment already has an established management solution. Instead, HP recommends using Insight Control in a limited capacity to support the existing environment while OneView becomes the new platform for supported systems.
Why C is correct:
- The Insight Control Management appliance can be configured to run in Update-only mode.
- This allows the customer to continue to manage firmware and updates for existing servers without fully relying on HP SIM for ongoing management.
- It provides a practical transition path when moving from older management tools to HP OneView.
- This approach aligns with mixed-generation environments where not all systems are ready to be fully managed by OneView.
Why the other options are incorrect:
A. Migrate all servers to HP OneView.
- This is too broad and not necessarily possible for all existing server generations.
- Older servers such as G5 may not be fully supported or ideal candidates for OneView migration.
B. Use HP OneView and HP SIM to manage all hosts.
- This is not the recommended target model.
- HP SIM and OneView are different management platforms, and running both as full management systems for all hosts is not the intended approach.
D. Continue to use HP SIM with Insight Control to monitor the existing environment and implement HP OneView to monitor G6 and newer servers.
- This is closer to reality than some other choices, but it does not address the update/management transition correctly.
- OneView is more than just monitoring, and this option does not reflect the recommended use of Insight Control Management appliance in Update-only mode.
In short, the most appropriate strategy is to use the Insight Control Management appliance in Update-only mode for the existing environment while adopting HP OneView as the new management platform where supported.

The correct answer is A. HP3 Par volume creation.
HP OneView 1.2 is designed to simplify infrastructure management by automating certain administrative tasks, especially around server, storage, and network provisioning in HP environments. In this version, one of the management functions it can automate is the creation of HP 3PAR storage volumes.
Why A is correct:
- HP OneView 1.2 includes integration with HP 3PAR storage systems.
- This allows administrators to automate storage provisioning tasks, including volume creation.
- This reduces manual steps and helps speed up deployment of server profiles and associated storage resources.
Why the other options are incorrect:
- B. Online migration from VCEM
- VCEM stands for Virtual Connect Enterprise Manager.
- HP OneView 1.2 does not automate online migration from VCEM as a management function.
- VCEM migration support came later and is not the specific automated function referenced here.
- C. Virtual Connect VLAN Auto discovery
- While HP OneView manages Virtual Connect environments, VLAN auto-discovery is not the automated management function highlighted in version 1.2 in the context of this question.
- It is not the best match for the described automation capability.
- D. Cisco Nexus 6001 switch configuration
- HP OneView is primarily focused on HP infrastructure management.
- It does not automate configuration of Cisco Nexus 6001 switches.
Summary:
HP OneView 1.2 automates HP 3PAR volume creation, making A the correct answer.